SPECIFICATIONS |
MODEL |
7730 |
AC WITHSTAND VOLTAGE |
|
Range |
Resolution |
Accuracy |
Output Voltage, ACV |
0-5000 |
1 |
±(2% of setting+ 5V) |
Output Frequency |
50Hz/60Hz ±100ppm, User Selection |
Output Waveform |
Sine Wave ,THD.<2% (Resistive Load), Crest Factor = 1.3 - 1.5 |
Output Regulation |
± (1% of output + 5V), From no load to full load |
SETTINGS |
Maximum Limit current, mA |
0.000 - 9.999 (0=OFF) |
0.001 |
± (2% of setting + 2 counts) |
10.00-30.00 |
0.01 |
Minimum Limit current, mA |
0.000 - 9.999 (0=OFF) |
0.001 |
± (2% of setting + 2 counts) |
10.00-30.00 |
0.01 |
Ramp-Up Timer, second |
0.1 - 999.9 |
0.1 |
± (0.1% + 0.05 sec) |
Ramp-Down Timer, second |
0.0 - 999.9 |
Dwell Timer, second |
0, 0.4 - 999.9 (0=continuous) |
Arc Detection |
1 - 9 ranges (9 is the most sensitivity) |
DC WITHSTAND VOLTAGE |
Output Voltage, DCV |
0-5000 |
1 |
±(2% of setting+ 5V) |
Output Ripple |
<4 %(5KV/10mA at Resistive Load) |
SETTINGS |
Maximum Limit, current, μA |
0 - 999.9 |
0.1 |
± (2% of setting + 2 counts) |
1000 - 10000 |
1 |
Minimum Limit, current, μA |
0.0 - 999.9 |
0.1 |
± (2% of setting + 2 counts) |
|
1000 - 10000 |
1 |
Ramp-Up Timer, second |
0.1 - 999.9 |
0.1 |
± (0.1% + 0.05 sec) |
Ramp-Down Timer, second |
0, 1.0 - 999.9 (0=OFF) |
Dwell Timer, second |
0, 0.4 - 999.9 (0=continuous) |
Ramp-HI, current |
>12 mA peak maximum, ON/OFF User Selection |
Charge-LO, current |
0.0 - 350.0 μA DC or Auto Set |
Discharge Time |
< 200 msec |
Maximum Capacitive LoadDC Mode |
1 μF < 1KV 0.08 μF < 4KV |
0.75 μF < 2KV 0.04 μF < 5KV |
0.5 μF < 3KV |
Arc Detection |
1 - 9 ranges (9 is the most sensitivity) |
INSULATION RESISTANCE |
Output Voltage, VDC |
50 - 1000 |
1 |
± (2% of setting + 2 counts) |
Short Circuit Current |
Maximum >12mA peak |
SETTINGS |
Maximum and Minimun Limit Resistance, MΩ |
0.05 - 99.99(Max – Limit: 0 = OFF) |
0.01 |
Same as Resistance MEASUREMENT Accuracy |
100.0-999.9 |
0.1 |
1000-50000 |
1 |
± (0.1% + 0.05 sec) |
Ramp-Up Timer, second |
0.1 - 999.9 |
0.1 |
Ramp-Down Timer, second |
0, 1.0 - 999.9 (0=OFF) |
Delay Timer, second |
0, 1.0 - 999.9 (0=continuous) |
0.1 |
Charge-LO, current, μA |
0.000 - 3.500 or Auto Set |
MEASUREMENT |
|
Range |
Resolution |
Accuracy |
Voltage, KV (AC/DC) |
0.00-5.00 |
0.01 |
± (1.5% of reading +2counts) |
Voltage, Vdc (IR only) |
0-1000 |
1 |
± (1.5% of reading + 2counts) |
AC Current, mA |
0.000-3.500 |
0.001 |
± (2% of reading + 2counts) |
3.00-30.00 |
0.01 |
DC Current, μA |
0.0 - 350.0 |
0.1 |
± (2% of reading + 2 counts) |
DC Current, mA |
0.300 - 3.500 |
0.001 |
3.00-9.99 |
0.01 |
Resistance, MΩ |
50-499V |
500-1000V |
|
50 – 499V 0.05–999.9, ±(7% of reading+2 counts) |
0.050-1.999 |
0.050-9.999 |
0.001 |
500 – 1000V |
2.00-19.99 |
10.00-99.99 |
0.01 |
0.10–999.9, ±(2% of reading+2 counts) |
20.0-199.9 |
100.0-999.9 |
0.1 |
1000–9999, ±(5% of reading+2 counts) |
200-50000 |
1000-50000 |
1 |
10000–50000, ±(15%of reading+2 counts) |
GENERAL |
Input Voltage |
115/230Vac±15% Auto Selection, 50/60Hz ± 5%, Fuse 4A Slow-Blo 250VAC |
PLC Remote Control |
Input: Test, Reset, Interlock, Recall Memory 1 through 10 |
Output: Pass, Fail, Test-in-Process, Reset Out |
Remote Output Relays |
125VAC@1AAC, 30VDC@ 0.5ADC |
Memory |
50 memories, 30 steps/memory |
Graphic Display |
240 x 64 dot resolution Monographic LCD /Contrast 9 Levels 1-9 |
Safety |
Built-in Smart GFI circuit,GFI trip current 450μA max, HV shut down speed: <1mS |
Interface |
Standard RS232, Optional PrinterPort with Date and Time Stamp or GPIB (IEEE-488.2). |
Security |
Programmable password lockout capability to avoid unauthorized access to test set-up program. |
Alarm Volume Setting |
Range: 0-9 ;0=OFF, 1 is softest volume, 9 is loudest volume. |
Calibration |
Adjustments are made through the fornt panel. Built-in Verification program. |
Automatic Calibration alert function to signal operator when calibration is due. |
Environment |
0-40℃, 20-80%RH |
Dimensions/Net Weight |
(W × H × D) 2U (430 × 89 × 400 mm)/13Kg. |
Option (Opt.735) |
DC Continuity Test Function (0.1A/ 0-2KΩ) at Rear Panel |
STANDARD ACCESSORIES |
Power Cord(10A) |
×1 |
Fuses |
×2 (Including a spare contained in the fuse holder) |
Interlock Disable Key(1505) |
×1 |
Hipot Test Lead ,1.5m(1101) |
×1 |
Hipot Return Lead ,1.8m(1102) |
×1 |
RS232 Link Cable 1.5m(1130) |
×1 |
MATRIX SCANNER MODULE (Opt.729) |
High Voltage Rating |
5KVAC/5KVDC |
Number of HV Channel |
8 |
MATRIX SCANNER MODULE (Opt.730) |
High Voltage Rating |
5KVAC/5KVDC |
Number of HV Channel |
4 |
DC CONTINUITY TEST FUNCTION (Opt.735) |
MEASUREMENT |
|
Range |
Resolution |
Accuracy |
Output Current |
DC 0.1A ± 0.01A, Max. |
Resistance Display |
0.00 – 19.99 |
0.01 |
± (1 % of reading + 5 counts) |
20.0 – 199.9 |
0.1 |
± (1 % of reading + 2 counts) |
200 – 2000 |
1 |
± (1 % of reading + 2 counts) |
SETTINGS |
Max-Limit, Ω |
0.00 – 19.99 |
0.01 |
± (1 % of setting + 5 counts) |
20.0 – 199.9 |
0.1 |
± (1 % of setting + 2 counts) |
200 – 2000 |
1 |
± (1 % of setting + 2 counts) |
Min-Limit, Ω |
0.00 – 19.99 |
0.01 |
± (1 % of setting + 5 counts) |
20.0 – 199.9 |
0.1 |
± (1 % of setting + 2 counts) |
200 – 2000 |
1 |
± (1 % of setting + 2 counts) |
Dwell Timer, second |
0.0, 0.3 – 999.9 (0 = continuous) |
0.1 |
± (0.1% + 0.05 sec) |
Resistance Offset, Ω |
0.00 – 2.00 |
0.01 |
± (1 % of reading + 5 counts) |